Tilta Camera Cage for BMCC 6K Advanced Kit - Black Tilta

Podrobný popis

The Tilta Advanced Kit for the Blackmagic Cinema Camera 6K is a finished cine rig: the full cage, the Xeno top handle, a left side power handle for an F570 battery, the 15mm LWS Baseplate Type VI with two rods, an SSD holder for the Samsung T5, the 15mm rod holder and a right-angle HDMI adapter. The camera is ready for a matte box, a follow focus and external recording.

The Advanced Kit builds on the Basic Kit and adds the 15mm LWS Baseplate Type VI with two 15 × 200 mm rods, a left side power handle for an F570 battery (12V micro DC 3.5/1.35 mm and 8V USB-C), the Type VI handle attachment and a Run/Stop cable for the USB-C port. The rig will then carry a matte box and a follow focus.

Key features

Detachable design

The right side arm module can be removed, turning the full cage into a half cage or a bare L-bracket. The lighter build suits a gimbal, the full cage handheld and tripod work. Two screws do it — you need not take the whole cage off the camera.

Works with the battery grip

With the bottom plate removed, the cage fits the body together with the original Blackmagic battery grip. The bottom plate expansion bracket braces against the grip, so the build stays rigid and the camera does not rock even with a heavier lens.

Three points of contact

The top plate meets the 1/4"-20 thread on top of the Full Frame body while two screws hold the cage from below. Three points of contact stop the body from twisting even with a heavy lens or a matte box hanging off the camera.

Threads wherever you look

Around the frame sit 1/4"-20 and 3/8"-16 threads with locating pins, cold shoe receivers, an ARRI-compatible rosette and a NATO rail for side handles. Accessories go exactly where you need them and will not rotate out of place.

You build the rig to suit the job: every thread has a locating pin beside it, so an EVF bracket, an SSD case, a run/stop cable, a rod holder or a baseplate will not twist out of alignment.

The bottom plate carries several 1/4"-20 threads for quick release plates and an Arca-Swiss profile, so the camera drops straight into the clamp of a DJI RS 3 or RS 3 Pro gimbal — and from there onto the tripod.

Run/Stop control from the side handle is not supported by the newest camera firmware. Powering the camera and accessories from the handle works as before.

Note: the BMD EVF does not fully clear the top plate of the cage. Take care when fitting and removing it so the viewfinder is not damaged.

• 1× Full Camera Cage for BMCC 6K – Black (TA-T64-FCC-B)
• 1× Slotted and Allen Key
• 1× Battery Grip Connector
• 1× Tilta Xeno Top Handle (1/4"-20 with locating pins) – Black (TA-XTH1-B)
• 1× Tilta SSD Drive Holder for T5 – Black (TA-SSDH-T5-B)
• 1× 15mm Rod Holder for BMPCC 6K Pro – Black (TA-T11-RH-B)
• 1× HDMI 90-Degree Adapter for BMPCC 4K/6K (TA-T01-HDA-90)
• 1× Tiltaing 15mm LWS Baseplate Type VI – Black (TA-BSP6-15-B)
• 1× Advanced Side Handle Run/Stop Cable for USB-C Port (RS-TA3-USBC)
• 1× Tiltaing Left Side Advanced Power Handle with Run/Stop (F570 battery) – Black (TA-LRH-57-B)
• 1× Tiltaing Advanced Left Side Handle Attachment Type VI – Black (TA-AHA6-L-B)
• 1× Aluminium Rod 15 × 200 mm, Black (R15-200-B) – 2×

• Compatibility: Blackmagic Cinema Camera 6K (Full Frame)
• Cage dimensions: 197.1 × 58 × 143.5 mm
• Cage weight: 281 g
• Material: aluminium alloy, stainless steel
• Interfaces: 1/4"-20 and 3/8"-16 threads with locating pins, cold shoe receivers, ARRI-compatible rosette, NATO rail, shoulder strap mounting slot
• Quick release: bottom plate with Arca-Swiss profile (DJI RS 3 / RS 3 Pro)
• Configurations: full cage, half cage, L-bracket
• Rod system: 15mm LWS, two 15 × 200 mm rods
• Power from the handle: 12V micro DC (3.5/1.35 mm) and 8V USB-C, Sony NP-F570 battery (not included)
• Colour: black

The dimensions and weight are those of the cage alone. The manufacturer does not state the weight of the complete kit.